RUT850 First Start
This Wiki page contains the online version of the Quick Start Guide (QSG) for the RUT850 LTE Router. Here you will find an overview of the various components found on the front and back sides of a RUT850 device, basic hardware installation, first login information, device specifications and general safety information. It is highly recommended that you acquaint yourself with with the Quick Start Guide before using the device. If you own a RUT850 device, you can also find a printed version of the Quick Start Guide in the device's package.
|5||Mobile network type LEDs|
|6||Mobile signal strength indication LEDs|
|2||GPS antenna connector|
|3||LTE antenna connectors|
- Remove the SIM card slot tray with the pin needle. Insert your SIM card and push the tray back into the router. Correct SIM card orientation can be seen in the figure below:
- Attach LTE and GPS antennas
- Connect the power adapter to the power socket located on the front panel of the device. Then plug the other end of the power adapter into a power outlet.
- Connect to the device wirelessly (SSID: RUT850_****).
Configure your computer (Windows)
- Enable the wireless network connection (go to Start → Control Panel → Network and Internet → Network and Sharing Center. In the left panel click the Change adapter settings link. Right click on Wireless Network Connection and select Enable).
- Setup wireless network adapter on your computer (right click on Wireless Network Connection and select Properties. After that select Internet Protocol Version 4 (TCP/IP) and click Properties).
- Select Obtain IP address and Obtain DNS server address automatically if they are not selected. Click OK.
- Right click on Wireless Network Connection and select Connect to see available wireless networks.
- Choose the wireless network RUT850_**** from the list and click Connect. Enter the WiFi password located on the device's label.
Login to device
- To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
- Use the following login information when prompted for authentication:
- After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router's WebUI before you change the password.
- When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to setup some of the router's main operating parameters.
- Go to the Status → Network page and pay attention to the Signal Strength indication. To maximize cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions (you can find information on signal strength recommendations here).
The RUT850 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.
|RF technologies||GSM, GPRS, EDGE, UMTS/HSPA+, LTE, GNSS, WiFi|
|Max. RF power||33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi|
|Bundled accessories specifications*|
|GSM/WCDMA/LTE antenna||690/900/1800/1900/2100/2700 MHz, 50 Ω, VSWR < 3.2, gain** 3.5 dBi, omnidirectional, FAKRA D female connector|
|GNSS antenna||1575.42~1602 MHz, 2.2-5 VDC, VSWR < 1.5, active total gain** 26 dB (typ.), RHCP polarization, FAKRA C female connector|
* Order code dependent.
** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.
Hereby, Teltonika declares that the radio equipment type RUT850 is in compliance with Directives: 2014/53/EU, 2014/35/EU, 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address: http://teltonika.lt/product/rut850/