RUT9xx Firmware
From Wiki Knowledge Base | Teltonika
This is the approved revision of this page, as well as being the most recent.
Main Page > Network products > RUT955 > RUT9xx Firmware
This page contains various firmware versions for RUT9xx devices.
| Firmware | Version | Changelog |
|---|---|---|
| Latest FW* | RUT9XX_R_00.06.03.2 | 2019.06.10 |
| Factory FW** | RUT9XX_R_00.06.03.2 | 2019.06.10 |
| Bootloader*** | RUT9XX Bootloader version 3.0.1 | 2017.02.14 |
* Latest FW - firmware candidate for release. This version will usually contain some new features and/or improvements (described in the Change log section of this article) but it hasn't been fully tested and approved by Teltonika's testing and technical support units.
** Factory FW - firmware used in mass production.
*** Bootloader - a program that loads the operating system or some other system software for the router after completion of the power-on self-tests; it is the loader for the operating system itself. You can find detailed instructions on how to upgrade your Bootloader to a newer version here.
FW checksums
A list of firmware checksums for RUT9xx firmwares uploaded in this page: checksum list
Change Log
RUT9XX_R_00.06.03.2 | 2019.06.10
- New features:
- Added port logging
- Added upload backup from lower firmware version support
- Added 4-pin I/O support for new RUT9 models
- Introduced auto APN selection feature
- Added SNMP GET requests for LAN1/LAN2/LAN3/WAN (or LAN4) status
- Hotspot TOS HTML support added
- GPL Teltonika 'twStreamApp' API for ThingWorx added
- Added UDP support for serial connections
- Improvements:
- Updated uci to version 2018-08-11
- Updated ubus to version 2018-10-06
- Updated ubox to version 2019-04-07
- Updated libubox to version 2019-02-27
- Updated openssl to version 1.0.2r
- Updated busybox to version 1.30.1
- Updated dropbear to version 2019.78
- Added reply after mobileon and mobileoff SMS Utilities commands
- Added access control disable confirmation
- Added data limit information in Hotspot landing page
- Modbus: added busy status return code while actions are executed
- GPS: added support for Input/Output
- Expanded VRRP configuration to support virtual MAC
- Added -U parameter to gsmctl for ussd commands
- Fixes:
- Mobile page fix
- Increased RMS HTTP Proxy resource limit
- Fixed LED indication setting
- Fixed input validation issues
- Mobile traffic graph fixes
- SIM Idle Protection test fix
- Services: Remove GRE and Hotspot from Status → Services window
- GPS speed calculation fix
- Mobile: set 1st context to IPv4
- RS232/RS485 service reload fixes
- Bootloader URL update
- Email to SMS validation and larger SMS send fix
- Fixed LED signal issue when reporting invalid signal
- Main WAN routes overwritten when USB Modem is used fix
- Added explanation text to operator control
- Remove WEP encryption method
- Cloud4wi profile fixes
- IPSec 'Allow WebUI access' with 'Redirect to HTTPS' fix
- SMS Utilities User group validation fix
- GPS Map was made compatible with Edge browser
- GPS Tab order fix
- Wireless regulatory domain and channel change fix
- GRE and GPS start/stop fix
- Minor NHRP bug fixes
- XHR authentication fixes
- DMVPN lua bug fix
- SMS Forwarding clarified WebUI options
- Hotspot local users data limit fix
- Setup Wizard Mobile 'Dialing number' disappears after save fix
- Setup Wizard: Validation fix
- Wireless SSID validation fix
- Bidirect mode connection problems fix
- GPS & SNMP Trap link fixes
- Validation for GRE Tunnel interface name added
- Force band validation fix
- VRRP status window fix
- PPTP server configuration when upgrading from old firmwares with keep-settings enabled fix
- Added GPS geofencing coordinate validation
- Added error return codes for fault conditions, changed writing register numbers for Modbus
- Fixed GPS time synchronization
- Output - Periodic Control form not visible on Chromium fix
- SIM Switch on mobile data limit fix
- Load Balancing validation for port numbers fixed, modified warning message
- Overview Bytes sent/received count fix
- Fixed sending data to AVL server
- OpenVPN configuration name fix
- DMVPN configuration count validation fix
- IPSec LAN access fix
- After editing WAN interface, redirect back to WAN page fix
- Wireless STA scanning when all AP are down fix
- SMS Gateway auto reply page fixes
- NTP time zone options fix
- Wake on LAN validation to prevent shell command execution via 'name' field
- GPS Input/Output SMS send fix
- RMS HTTPS proxy fix
- Fixed RMS WAN State and WAN IP
- MQTT bridge with SSL/TLS connection fix
- Use DNS servers advertised by peer not saving fix
- Wget reboot logging fixes
- Periodic Control do not show timeout if it is disabled fix
- QoS speed limitation fix
- Added additional band support for some models
RUT9XX_R_00.06.02.2 | 2019.04.23
- Fixes:
- GPS related fixes
- SDK compilation fixes
RUT9XX_R_00.06.02 | 2019.04.05
- New features:
- Added Modbus master feature
- Added Modbus data sender feature
- Added NMEA forwarding, Geofencing, NTP calculation, AVL forwarding, HTTPS forwarding, other satellite support to GPS functionality
- Added DMVPN service
- Impelemented NHRP protocol
- Improvements:
- Updated xl2tpd to version 1.3.13
- Added "use as default gateway" option to SSTP
- Added XT25F128B flash support
- Shared-keys option added to Strongswan
- Auto option selection added to Strongswan
- Added GRE Tunnel source selection from interfaces and ability to write in the local IP
- Added ability to create VLAN 0
- Fixes:
- Fixed Event Log reporting over FTP
- Multiple OpenVPN fixes
- IPSec start order fix
- IPSec configuration loss fix
- IPSec sha512 and sha384 support fix
- IPSec IKEv2 restart loop fix
- L2TP stability issue fixes
- L2TP service restart after config change fix
- USB to serial multiple minor bug fix
- Samba multiple bug fix
- Wireless Station availability when two or more Access Points are created fix
- Input/Output analog calculator fix
- Wget Reboot disable fix
- SMS Utilities, 'more' command SMS text customisation fix
- SMS Utilities GPS ON/OFF fix
- SMS Utilities 'uci show' command fix
- Multiple SMS Utilities remote configuration fixes
- Use WAN as LAN fix
- Wake on LAN use WAN as LAN fix
- Authorization on LTE network fix
- Restore Point file download fix
- LED issue when rebooting router with reset button fix
- LED issue when there is no connection fix
- SSTP interface up after being disabled fix
- MQTT Publisher WAN IP retrieval fix
- Static leases, MAC address list fix
- Static Routes, PPTP interface creation fix
- SMS Utilities User groups synonymous numbers '00XXX' & '+XXX' fix
- Hotspot Restricted Internet Access fix
- Hotspot session in use by user deletion fix+
- Hotspot Walled Garden fix
- Hotspot Statistics window contains non-hostpots fix
- Hotspot authentication mode validation fix
- VLAN, LAN Network configuration backup fix
- VRRP fix
- Call utilities, mobile data ON/OFF without config write fix
- MQTT multiple bug fixes
- Output Scheduler fix
- Profiles: output scheduler update fix
- Maximum length SMS message send fix
- DDNS sleep after check interval and force interval fix
RUT9XX_R_00.06.00.4 | 2019.03.12
- Fixes:
- Samba fix
RUT9XX_R_00.06.00.3 | 2019.03.08
- Fixes:
- Special case 3G to 4G fix
RUT9XX_R_00.06.00.2 | 2019.03.07
- New features:
- Added Wake on LAN feature
- Added SMS Utilities Wake on LAN rule
- Added Global module connection support
- Improvements:
- Changed RMS communication protocol to MQTT from OpenVPN
- Added informational text to Proxy based content blocker page
- Improved wording in Load Restore Point section
- Updated curl to version 7.64.0
- Updated OpenSSL to version 1.0.2q
- Fixes:
- UPNP not starting, reappearing leases fixes
- Removed NOTRACK from firewall rules
- RS232/RS485: allow DNS NTRIP address
- DDNS Process kill fix
- Multiwan fix
- Added rule validation to Load Balancing
- rpcd broken pipe fix
- Daily mobile traffic deletion fix
- Fixed mobile traffic logging graph issues
- CLI Connect button fix
- Data only SIM support fix
- Limit guard Widget fix
- Sodog related fixes
- Hotspot Advertisement address error message fix
- SSTP fix
- SIM switch related fixes
RUT9XX_R_00.05.04 | 2019.01.14
- Improvements:
- Added IP allocation for users in L2TP server
- SMS utilities add 'more' functionality
- Added modem band display in Mobile page
- Fixes:
- Remote access information fix
- Fixed static route application for PPTP, L2TP servers
- Fixed PPTP passwords file override
- L2TP IP-range change fix
- Fixed firewall rules that apply for hotspot firewall zone
- SMS Utilities web access control rule fix
- Wireless status and mobile uptime fixes
- Fixed active connections on Fallback WAN
- Fixed routing table display
- Setup Wizard LAN DHCP fields not hidden when DHCP is unchecked fix
- Fixed GRE Tunnel connection
- Fixed static routes table view with VPN interfaces
- Enabled NTP to run server and client simultaneously
RUT9XX_R_00.05.03.4 | 2018.12.20
- Fixes:
- SSH security fix
- Mobile page fix
RUT9XX_R_00.05.03.3 | 2018.12.11
- New features:
- Added SSTP VPN protocol
- Added force network bands support for RUT9xx H*****, U***** and T***** product codes
- Added STunnel feature to VPN services
- Improvements:
- Added every WAN interface selection to QoS
- Updated VRRP to latest version
- Added MAC address range support for WiFi MAC filter
- Fixes:
- Enabled "Enter" key on login form
- Mobile WAN IP display in overview
- SMS status WAN IP with multiwan fix
- Fixed WAN failover metrics and priorities
- Some additional WAN failover fixes
- Update Teltonika contact address in Licenses page
- Fixed lua dispatcher error after reboot
- Overview OpenVPN widget fix
- Associated wireless stations display fix
- PPTP default gateway set and delete fix
- GRE Tunnel delete after button press fix
- L2TP network restart after L2TP connection loss fix
- Wireless connection loop fix
- Modem related updates
- Disabled DHCP request in bridge mode
- Keep data limit count after firmware upgrade with keep settings fix
- WiFi STA+AP fix
- GPS related fix
- SNMP signal value type and memory leak fixes
- Modbus serial read gateway timeout fix
- Modbus set APN and memory leak fix
- Serial over IP ASCII full character support fix
- SMS Utilities check for incoming SMS fix
- Events Reporting firmware upgrade fix
- Mobile WAN IP fix
- L2TP network restart after client delete with default gateway set fix
- Hotspot user validation fix
- Added OpenVPN service restart when TLS Password is changed
- Redirect to different LAN IP after configuration backup, restore and firmware upgrade fix
- NTP time synchronisation after WebUI configuration fix
- Setup wizard wireless channel select fix
- Data collection counter fixes
- Fixed inactive SNMP Input/Output traps
- SNMP Hotspot and serial values fix
- Log to flash limited to 1MB
RUT9XX_R_00.05.02.6 | 2018.11.05
- Fixes:
- Overview mobile WAN IP display fix
RUT9XX_R_00.05.02.5 | 2018.10.26
- Fixes:
- Removed ability to use username and password without APN
- Updated to latest modem version
- Changed dhcp usage on mobile interface
RUT9XX_R_00.05.02.3 | 2018.10.22
- New features:
- Added event log entry when clearing mobile data limit
- Fixes:
- Data limit calculation fixes
- SIM switch: data limit check fixes
RUT9XX_R_00.05.02.2 | 2018.10.12
- Fixes:
- Troubleshoot: sensitive information (usernames and passwords) removal from router configuration
- DDNS IP source changing fix
- Overview VRRP widget status fix
- OpenVPN name validation with special symbols check fix
- SMS Forwarding number check with 00 code with listed numbers fix
- Overview SMS counter widget fixes
- Firewall and UPnP page display fixes
- Periodic SIM Switch check fix
- Operator selection fix
- SNMP MIB values and file format fix
- OpenVPN configuration section name compatibility fix
- Call Utilities: 4G-only mode warning fix
- Mobile traffic data usage delete fix
- Disabled passthrough and bridge selection when multiwan is enabled
- Log to flash limited to 1MB
RUT9XX_R_00.05.02 | 2018.10.01
- New features:
- Added Relayd function
- Added ability to create multiple geofencing zones
- Added support for NTFS disks
- Enabled diffie-hellman-group14-sha1 key exchange algorithm
- Improvements
- Changed default VLAN to vid 0, added ability to tag WAN port
- Added ebgp-multihop option to BGP
- Added Modbus parameters for GPS information
- Added custom IPsec option field
- Disabled Hotspot users ability to reach LAN devices and WebUI
- WAN Failover: add option to execute command
- Made Wired (Main) + Mobile (Failover) as default configuration
- Enabled connection to RMS by default
- Some RMS page updates
- Added default LAN IPv6 address
- Fix:
- OpenVPN server authentication change fix
- Events reporting rule enable fix
- PPTP use as default gateway option fix
- Language translation fixes
- RS232/RS485 synchronization bug fix when using NTRIP with GPS coordinates
- Operator list fixes
- USB to Serial firewall rules fix
- SMS Utilities rule not enabled exit fix
- MQTT remote address datatype fix
- GSMD: remove old info from help
- Some Hotspot functionality fixes
- Input/Output User groups fix
- DHCP server lease time fix
- Dynamic routes fixes
- Static Routes fix
- Mobile Passthrough mode fix
- Events Log Report configuration validation fixes
- WiFi updates and security fixes
- Overview WAN wiki link fix
- Overview Hotspot widget fix
- SIM Idle Protection Test WAN IP fix
- Samba network share discovery fix
- SIM card switch on data limit fix
- Mobile data bytes reset on 4GB fix
- Hotspot start after reboot fix
RUT9XX_R_00.05.01.8 | 2018.09.10
- Fixes:
- Config restore fix
- RS-232 serial over IP fix
- CLI fix for RMS
RUT9XX_R_00.05.01.5 | 2018.08.02
- New features:
- Added PDU forwarding function
- Added new logic for operator whitelist/blacklist
- Updated mobile operator database
- Added Firmware update information
- Added information text in Emailt to SMS page
- Added wiki link to an IP type next to WAN IP
- Added Graphs/Signal strength: UMTS network type signal
- Added Operators list: periodic network scan if fail to connect to operator on first time
- Added SLIP protocol with slattach software into the router
- Added automatic IP refresh in WAN page
- Added VLAN LAN IP start and end automatic update
- Fixes:
- DDNS Force update
- Configuration Wizard: LAN page redirect fix
- Overview: WAN IP fix
- Fixed Troubleshoot: TCP dump
- Access Control: Add Redirect to HTTPS information
- Service Status: QoS status
- Hotspot: Parameter validation
- Overview: OpenVPN widget
- PPTP: Fix interface metric on multiwan with PPTP
- Nerwork -> WAN Mode translate
- DHCP range display in VLAN page
- Change 'Backup WAN' to 'WAN Failover'
- Linux: CVE-2017-18017
- OpenVPN: remote IP address validation to not include route LAN subnet
- GRE: updated keep alive to work with cisco routers
- WebUI: NTP Time servers page fix
- Call Utilities: reboot action partial message
- WebUI: sim_switch: add ICMP host field validation
- Hotspot: data limit fix
- Security: CLI: updated shellinabox to 2.20, changed CLI WebUI page
- WebUI: DDNS: Force IP renew
- WebUI: SMS counter widget
- WebUI: Hotspot: security
- PPP: add default route
- WebUI: Hotspot: Protocol and HTTPS redirect option
- WebUI: Mobile Traffic Usage Logging
- WebUI: Administration added hostname length limit (32 symbols)
- OpenVPN: Add RMS service fix
- libgsm: Prevent crash on failed libusb init
- uHTTPd: Disable stderr option
- SMS Utilities: Prevent crash when reading config
- Mobile: Service mode selection fix (Mantis ID: 0021909)
- WebUI: Prevent redirection to HTTPS by default
- WebUI: Add hint when accessing CLI without certificate
- SMS Utilities: Prevent stopping application on empty reports config
- CLI: Use correct service port
RUT9XX_R_00.05.00.5 | 2018.05.30
- New features:
- Added forced password change
- New firmware versioning system
- Fixes:
- Fixed SMS PDU decoding sender number
- Fixed RMS connection status display in Overview window
- SIM Switching fix
- Updated Hotspot login page parameters (MAC parameter)
RUT9XX_R_00.04.233 | 2018.04.26
- Fixes:
- Minor Hotspot fixes (CVE-2018-17532)
- Minor SIM Switch fixes
- Minor opkg fix and package update
RUT9XX_R_00.04.199 | 2018.04.18
- Improvements:
- Upgraded SIM Switch speed
- Upgraded OpenVPN with the possibility to upload CRL files
- Added IP aliases description and advanced features
- Added additional DPD option to IPsec configuration
- Fixes:
- Disabled saving password with the Enter key on WebUI
- Firewall User Script fix
- OpenVPN TLS clients fix
- Some IPsec functionality fixes
- Fixed all VPN shutdown on delete
- Mobile Passthrough mode bad netmask fix
- Call Utilities write to config fix
- Minor Input/Output fixes
- Fixed RMS connection retry time
- Signal Strength display fix for HSDPA+HSUPA network type
RUT9XX_R_00.04.172 | 2018.04.10
- New features:
- Added RMS connection page to Setup Wizard
- Added link to Teltonika wiki in the router's WebUI
- Updated Overview conifugration with Remote Monitoring widget and wiki icon
- Improvements:
- Upgraded to faster SIM switching logic
- Fixes:
- Fixed OpenVPN TLS/Password client route pushing
- Fixed GPS bug that caused 100 % CPU usage when using I/O
- Fixed password saving with the "Enter" key
- Removed RS485 echo
- Fixed Event Log bug that caused Call events not showing up in the log
- Fixed SMS-Utilities openvpn status rule
RUT9XX_R_00.04.161 | 2018.03.26
- Improvements:
- Improved SSH security
- Fixes:
- Fixed deleting SMS messages function in SMS Utilities
- QoS bug fix that caused it to work even if it was disabled
- LTE only mobile data connection fix
- Minor Kernel fix
- Minor functionality fixes for when there is no SIM card inserted
RUT9XX_R_00.04.153 | 2018.03.16
- Fixes:
- IPsec fix for use with multiple WANs
- Fixed a bug that caused different WAN IPs to be displayed in the Overview and WAN windows
- SMS Forwarding to HTTP fix
- SMS Utilities functionality fixes
RUT9XX_R_00.04.147 | 2018.03.08
- New features:
- Added L2TP tunnel watchdog.
- Fixes:
- PPP connection type fix
- SMS Utilites vpnon/vpnoff rule fixes
- Added GRE-Tunnel fix that prevents problems when switching profiles
- OpenVPN status display fix
- SMS Forwarding to Email fix
RUT9XX_R_00.04.125 | 2018.02.27
- Improvements:
- Added ICCID print, for dynamic parameters
- Added reload function for GRE Tunnel if SIM Switch ocured
- Added SIM card option for GRE tunnel
- Fixes:
- SMS Utilities forward to HTTP fix
- Network Shares USB drive safe removal fix
- Some changes to config hierarchy
- Wget Reboot fix
- Input/Output SIM Switch rule fix
RUT9XX_R_00.04.112 | 2018.02.20
- Fixes:
- Small fix for HTTPS access when DMZ is enabled
- Updates to Firmware Upgrade verification
- L2TP unused UCI option removed
- Minor fixes to VPN use with Multiwan
- Format style fixes for VPN pages
RUT9XX_R_00.04.103 | 2018.02.14
- Fixes:
- SMS Counter database fix
- IP renewal by APN fix
- Firmware verification bug fix
- Call Utilities rule enable fix
- Wget Reboot modem restart fix
RUT9XX_R_00.04.94 | 2018.02.12
- New features:
- Added Printer Server functionality that allows control of a printer that connects to the router via USB cable
- Improvements:
- Improved RS232/RS485 Over IP function so that the server can communicate with multiple clients at the same time
- Added automatic Firewall rules that allow remote access to the router's WebUI when DMZ is enabled
- Fixes:
- Some minor Samba fixes in the WebUI
- OpenVPN username and password validation fix
- Fixed VPN service restart when in use with Multiwan
- Site Blocking file parsing fix
- Some updates to the router's config file system
- Firmware check fix
RUT9XX_R_00.04.75 | 2018.01.30
- Fixes:
- APN bug fix
- Added modem Firmware update package
- Some minor OpenVPN username and password requirement fixes
RUT9XX_R_00.04.64 | 2018.01.23
- Improvements:
- SMS Utilities rule configuration pages supplemented with information about SMS text format
- Disable NAT function moved from VPN to Firewall page
- Fixes:
- Minor fix to Hotspot functionality
- Minor fixes to Firewall confg
- Fixed Mobile Data Limit byte count storage
- RS232/RS485 Modbus functionality fixes
RUT9XX_R_00.04.57 | 2018.01.17
- Improvements:
- Added special character support for OpenVPN tunnel names
- Added binero.se to DDNS service list
- Fixes:
- Fixed Write to config function for SMS Utilities mobileoff rule
RUT9XX_R_00.04.48 | 2018.01.12
- New features:
- Added RS232 over IP serial data as email feature
- Fixes:
- Fixed MQTT bug where you couldn't remove TLS/SSL option once selected
- Fixed GPS hostname data type check
- Fixed DHCP lease time validation in LAN and Setup Wizard
- Updated IPsec stop function
- Site blocking White List fix
- Modem GPS related bug fix
RUT9XX_R_00.04.38 | 2018.01.08
- Fixes:
- Changed Mobile Data Limit representation in the Overview window
- Fixed GPS Fix status display bug
RUT9XX_R_00.04.32 | 2018.01.04
- New features:
- Added Wget Reboot function
- Added RS232/485 initiation string option for Modem mode
- Fixes:
- Samba user creation fix. Added a user limit of 2999 users
- Some minor grammatical and data type fixes in the router's WebUI
- Added a function that restarts services when using the SMS Utilities uci rule
- Input/Output Scheduler backup fix
- Some fixes to the style of the Administration page
- Network Operators White List fix
- Mobile connection stability fix
RUT9XX_R_00.04.12 | 2017.12.22
- New features:
- Added IPsec support for multiple clients
- Improvements:
- Updated troubleshoot package with IPsec status
- Added WebUI notice for SIM Switch on Data limit
- IPsec instances limit set to 5
- Dynamic list limit set to 100
- Fixes:
- Wi-Fi security fix
- Firmware update fix due to 04 FW version
- SIM Switch back to primary SIM after Data or SMS limit fix
- Fixed bug that didn't allow hostnames to be used as Ping Reboot
RUT9XX_R_00.03.985 | 2017.12.14
- New features:
- Added left and right firewall options to IPsec configuration
- Fixes:
- Fixed some minor grammatical errors
- SIM PIN bug fix
- Some minor fixes to SMS and Call Utilities
- Fixed loading gif spinner bug that caused it to spin endlessly
- SMS Gateway form validation fixes
- Post/Get configuration fix
- Fixed empty value insertion for IPsec local LAN
- Fixed iptables rule that didn't allow Limit Guard to account traffic
- Some minor PPTP Server and Client fixes
- Fixed mobile disconnection bug
RUT9XX_R_00.03.965 | 2017.12.07
- New Features:
- Added NAT Helper control page to the Firewall section
- Improvements:
- Added IPsec Multiwan support for transport mode
- Fixes:
- Changed data type for storing Data limit network stats
- Added some default Firewall rules needed for SIM Switch
- SIM Switch on Data limit now uses limit_guard for counting data
- Some stylistic changes to router's WebUI
- Fixed Call Utilities calling from User Group bug
- Fixed OpenVPN Static key bug
RUT9XX_R_00.03.946 | 2017.12.01
- New features:
- Added OpenVPN Client key decryption password field
- Improvements:
- Updated Dynamic DNS service
- Fixes:
- OpenVPN Server configuration save fix
- Multiple PPTP clients in LAN fix
- Fixed Realtime Traffic graphs with PPP type connection
- Fixed PPP connection type data usage collecting
RUT9XX_R_00.03.923 | 2017.11.24
- Fixes:
- Wi-Fi Station with WPA-Enterprise fix
- Fixed Wi-Fi Access Point SSID mismatch when adding new Access Points
- Fixed no data connection bug when Operator is added to the White List
- Added fix that makes sure password fields glow red after entering incorrect data
- Fixed SMS Utilities bug that caused Router Name not being displayed in status messages
- SMS Counter fix
- Some security fixes
- Some modem functionality fixes that prevent not switching to LTE
- SIM Switch logic fixes
RUT9XX_R_00.03.906 | 2017.11.20
- New features:
- Added WPA-Enterprise support
- Added Hotspot Landing page URL parameters config
- Added Host list file feature that allows uploading a list of hosts to Site Blocking and Proxy Based Content Blocker
- Added RS232/RS485 Serial type: Modem option
- Added SNMPv3 support
- Added Huawei USB modem support added
- Fixes:
- Added reboot patch for Event Log messages
- Use IPv4 Only fix that caused not using default context ID
- Fixed reboot with button issue
- Added Multiwan checking for L2TP fix
- Added default static route selection for L2TP
- Some kernel logging fixes
- Updated iptables 1.4.21 release to 2
- Updated busybox package to 1.24.2
- Fixed OpenVPN NAT configuration
- Web Filter model fix
- SMS Counter fix
- Fixed Bridge mode bug that prevented devices from getting an IP address when APN was entered
- Fixed connection to hidden Wi-Fi Access Point
RUT9XX_R_00.03.850 | 2017.11.03
- New features:
- Added NETMAP functionality
- Fixes:
- Some Limit Guard fixes
- Some GPS functionality fixes
- Mobile sent/received data added to TR-069
- Fixed start up of SD card
RUT9XX_R_00.03.832 | 2017.10.25
- Improvements:
- Added network and cell information
- Fixes:
- RS232/RS485 fix for flow controll settings and console mode
- Internet Explorer WebUI bug fix
- Fixed new FOTA version notice
- Added network and cell information
Bootloader Change Log
RUT9XX Bootloader version 3.0.1 | 2017.02.14
- Improvements:
- Increased DDR voltage
NOTE: there are two Bootloader files in the archive. Which file should be used depends on circumstances. More details on this and how to upgrade the Bootloader to a newer version can be found here.
RUT9XX Bootloader version 3.0.0 | 2016.06.30
- Improvements:
- Upgraded U-boot
RUT9XX Bootloader version 2.0.0 | 2016.01.22
- Improvements:
- Removed SafeMode feature
RUT9XX Bootloader version 1.0.0 | 2014.11.14
- New features:
- Released U-boot
