RUTX09 First Start

From Wiki Knowledge Base | Teltonika
Revision as of 17:03, 6 November 2019 by Dziugas (talk | contribs) (Protected "RUTX09 First Start" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))

(diff) ← Older revision | Approved revision (diff) | Latest revision (diff) | Newer revision → (diff)
Main Page > Network products > RUTX09 > RUTX09 First Start

This Wiki page contains the online version of the Quick Start Guide (QSG) for the RUTX09 LTE-A Cat6 Router. Here you will find an overview of the various components found on the front and back sides of a RUTX09 device, basic hardware installation, first login information, device specifications and general safety information. It is highly recommended that you acquaint yourself with with the Quick Start Guide before using the device. If you own a RUTX09 device, you can also find a printed version of the Quick Start Guide in the device's package.

Rutx09 hd 2 demo.jpg

Front view

No. Description
1 WAN type LEDs
2 Mobile connection type LEDs
3 Mobile signal strength LEDs
4 SIM card holders
5 SIM needle
6 LAN LEDs
Networking rutx09 manual panels front v1.jpg
7 WAN LED
8 Power socket
9 Reset button
10 LAN Ethernet ports
11 WAN Ethernet port
12 Power LED

Back view

No. Description
Networking rutx09 manual panels back v1.jpg
1 Mobile antenna connectors
2 GPS antenna connector
3 Grounding screw
4 USB connector

Connectors

Power socket pinout
No. Description Wire color
1 Power Red
2 Ground Black
3 Input Green
4 Output White
Trb142 power socket pinout v3.png

Hardware installation

  1. Remove the SIM card slot tray with the pin needle. Insert your SIM card and push the tray back into the router. Correct SIM card orientation can be seen in the figure below:
    Rutx09 sim card insertion v1.jpg
  2. Attach LTE and GPS antennas
  3. Connect the power adapter to the power socket located on the front panel of the device. Then plug the other end of the power adapter into a power outlet.
  4. Connect to the device using an Ethernet cable by plugging it into any LAN port.

Configure your computer (Windows)

  1. Enable the Ethernet network connection (go to Start → Control Panel → Network and Internet → Network and Sharing Center. In the left panel click the Change adapter settings link. Right click on Ethernet Network Connection and select Enable).

    Qsg rutxxx enable wireless connection v2.png

  2. Setup Ethernet network adapter on your computer (right click on Ethernet Network Connection and select Properties. After that select Internet Protocol Version 4 (TCP/IP) and click Properties).
  3. Select Obtain IP address and Obtain DNS server address automatically if they are not selected. Click OK.

    Qsg rutxxx obtain ip address automatically v2.png

Login to device

  1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
  2. Use the following login information when prompted for authentication:

    Qsg rutxxx routers web interface v2.png

  3. After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router's WebUI before you change the password.
  4. When you change the router's password, the Configuration Wizard will start. The Configuration Wizard is a tool used to setup some of the router's main operating parameters.
  5. Go to the Status → Network page and pay attention to the Signal Strength indication. To maximize cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions (you can find information on signal strength recommendations here).

    Qsg rutxxx login to device v2.png

Safety information

The RUTX09 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

Radio specifications
RF technologies UMTS/HSPA+, LTE-A, GNSS
Max. RF power 24 dBm@WCDMA, 23 dBm@LTE
Bundled accessories specifications*
Power AC/DC power adapter 12 V 1.5 A, 4 pin plug
GSM/WCDMA/LTE antenna 698~960/1710~2690 MHz, 50 Ω, VSWR < 3.0, gain** 2 dBi, omnidirectional, SMA male connector
GNSS antenna 1575.42~1602 MHz, 2.2-5 VDC, VSWR < 1.5, active total gain** 28 dB (typ.), RHCP polarization, SMA male connector

* Order code dependent.

** Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

Qsg rut950 manual.PNG This sign on the package means that is necessary to read the User's Manual before you start using the device.

Qsg rut950 recycle.PNG This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.